How to Replace a Bathtub in Your Bathroom
How to Replace a Bathtub in Your Bathroom
Blog Article
We've encountered the article relating to A Step-by-Step Guide to Installing a Bathtub directly below on the internet and decided it made perfect sense to relate it with you here.
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Changing an old bathtub with a new one is also a moderately difficult project. If the old tub is easily easily accessible, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the new one. See to it you have actually qualified yourself for the work and also fit attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to think about employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your restroom if you have actually currently purchased a new bathtub as well as don't require to alter the setup of your previous supply of water pipelines.
Your tools and product checklist should make up the following:
Planning for the Installation
To start with, the supporting structure supplied with the bathroom must be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of getting rid of the existing taps can be quite problematic because of the limited accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the very same for the various other faucet.
Turn on the supply of water and check all joints and brand-new pipework for leakages and also tighten them if essential. Load the tub and also check the overflow electrical outlet and also the typical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at least when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet connectors. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing complications with moisture and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can break relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is advisable to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very curious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed reading our article. Sharing is nice. Helping others is fun. Thank you for taking the time to read it.
This Resource Report this page